How to prolong the service life of the print head
2012-11-19 13:41:15点击量：591
The print head is the most fragile tube printer device. It is like a car tire is a consumable, will eventually damage If you pay attention to maintenance, however, will be able to extend the life of the print head.
1, pre- maintenance
In order to play important role, it should be every two weeks or the three weeks clean the print head,Note that when cleaning the print head to the need to prevent a hard object (such as rings, etc.) to prevent scratching the print head, and with grounded metal band or anti-static pad to prevent electrostatic damage to the print head.
Firs Power off tube printer, gently blow away the dust, then with 70% of the alcohol-soaked cotton swab, wipe the print head surface and tube pritner of the mechanical parts, such as: rubber roller, ribbon sensor. Multiple "reversal" key, side turn while wiping swab dirty do not reuse. Do not use any hard metal or tools (such as screwdrivers, etc.) to wipe or scrape the printhead pollutants.
2, Factors that caused the premature failure of the print head.
Friction- Label/ tube / ribbon through the long-term movement of the print head will wear the protective layer of the ceramic coating, the print head acupuncture (points) exposure and ultimately damage.
3,In order to avoid scratches
Periodically clean the print head and the use of high-quality smooth and thermal transfer ribbons with film backing layer to reduce friction;
Minimize the pressure of the print head and print temperature;
The width of the ribbon width than the label to prevent expose the print head label abrasions.
The ribbon backing layer caused by dirty - print head thermal transfer ribbon pollution will need a high-temperature, high-pressure, high-speed high-set value: the accumulation of pollutants on the print head (pin) caused by heat transfer barriers affect print maplike quality; pollutants gradually increase print quality and print material looks dull or even damage to the print (pin).
4,Caused by dirty To avoid ribbon back layer
The need to use a thermal transfer ribbon to the back layer of protection, be sure to refer to the non-sticky ribbon ribbon, electrostatic dissipative and lubrication;
Cleaning the rubber roller, you must select reverse, so as not to damage the print head;
Be sure to use clean tube;
Often do print head maintenance;
We protect the print head film can be quick and easy to remove the print head garbage accumulate
5, print head warranty
Recommended to use the ribbon suppliers to achieve the best print results, and can reduce the wear on the print head;
Lead to the damage of the print head on the use of the ink ribbon of the non-provided by suppliers, the supplier is not take any responsible.
1, pre- maintenance
In order to play important role, it should be every two weeks or the three weeks clean the print head,Note that when cleaning the print head to the need to prevent a hard object (such as rings, etc.) to prevent scratching the print head, and with grounded metal band or anti-static pad to prevent electrostatic damage to the print head.
Firs Power off tube printer, gently blow away the dust, then with 70% of the alcohol-soaked cotton swab, wipe the print head surface and tube pritner of the mechanical parts, such as: rubber roller, ribbon sensor. Multiple "reversal" key, side turn while wiping swab dirty do not reuse. Do not use any hard metal or tools (such as screwdrivers, etc.) to wipe or scrape the printhead pollutants.
2, Factors that caused the premature failure of the print head.
Friction- Label/ tube / ribbon through the long-term movement of the print head will wear the protective layer of the ceramic coating, the print head acupuncture (points) exposure and ultimately damage.
3,In order to avoid scratches
Periodically clean the print head and the use of high-quality smooth and thermal transfer ribbons with film backing layer to reduce friction;
Minimize the pressure of the print head and print temperature;
The width of the ribbon width than the label to prevent expose the print head label abrasions.
The ribbon backing layer caused by dirty - print head thermal transfer ribbon pollution will need a high-temperature, high-pressure, high-speed high-set value: the accumulation of pollutants on the print head (pin) caused by heat transfer barriers affect print maplike quality; pollutants gradually increase print quality and print material looks dull or even damage to the print (pin).
4,Caused by dirty To avoid ribbon back layer
The need to use a thermal transfer ribbon to the back layer of protection, be sure to refer to the non-sticky ribbon ribbon, electrostatic dissipative and lubrication;
Cleaning the rubber roller, you must select reverse, so as not to damage the print head;
Be sure to use clean tube;
Often do print head maintenance;
We protect the print head film can be quick and easy to remove the print head garbage accumulate
5, print head warranty
Recommended to use the ribbon suppliers to achieve the best print results, and can reduce the wear on the print head;
Lead to the damage of the print head on the use of the ink ribbon of the non-provided by suppliers, the supplier is not take any responsible.
FAQ
